不同改良措施对排土场土壤微形态影响的试验研究

以铁矿排土场废石土为研究对象,自制模型试验装置,设计4种基质改良方法,开展SEM检测实验,并应用IPP软件对SEM照片进行定量化分析,研究在不同改良措施下对铁矿排土场土壤微结构的影响。结果表明：单施3%有机肥土壤孔隙度为16%,与对照组排土场原矿土相比增加了60%。复合施用3%有机肥、掺拌30%的黄土的处理孔隙度达到最大33%。单施3%有机肥、5%有机肥对土壤大团聚体含量皆有显著的促进作用,复合施有机肥、掺拌黄土的处理与单施有机肥的处理对比,土壤大团聚体含量增加并不显著。各改良措施的MWD与FMD均随着土壤中大团聚体的含量增加而增加。     

Experimental and Modeling Studies on the Chemical Vapor Infiltration with Respect to the Effects of Thermal Gradient and Other Operating Parameters

Effects of operating parameters in the thermal gradient chemical vapor infiltration of propane such as thermal gradient, diffusion, infiltrations time, and concentration of propane were studied by focusing on the visualizations of the intrinsic effects of these parameters. A uniform deposition in the preform was obtained with a gradually increasing temperature along the gas flow. The uniformity of deposition through the preform got improved with increasing deposition time. Results of numerical modeling estimated the experimental data very well when the pre-exponential factor of the overall rate of carbon deposition from propane reported by Vaidyaraman[1] was multiplied by 4. The average density of a preform increased by about 3 times from 0.38 to 1.15 g/cm3 after 60 hr deposition with a thermal gradient under the conditions of 3% propane in nitrogen and 840 to 900 ℃.     

Enhanced photoluminescence of CoWO<Subscript>4</Subscript> in CoWO<Subscript>4</Subscript>/PbWO<Subscript>4</Subscript> nanocomposites

CoWO₄/PbWO₄ nanocomposites were successfully synthesized at room temperature (RT) by co-precipitation route without using any templates or surfactants and sintered at 600 °C for good crystallization. The sintered samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy and Zeta potential measurements. UV–Visible diffuse reflectance spectroscopy, photoluminescence (PL) and PL lifetime were studied at RT. The results indicate that the composites have two-phase composition: CoWO₄ and PbWO₄. SEM micrograph and zeta potential measurements reveal particle agglomeration. The intrinsic PL peak emission at 467 nm of CoWO₄ nano sample was enhanced upto four times by optimizing the atomic ratio of Pb/Co concentration. The interconnected interface of CoWO₄/PbWO₄ nanocomposites could have led to increase in number of recombination of electron hole pairs in CoWO₄ and enhanced its intrinsic PL emission intensity. The mechanism of enhanced PL emission for the CoWO₄/PbWO₄ nanocomposites can be attributed to charge transfer between [WO₄]^2? and [WO₆]^6? complexes due to intra particle agglomeration leading to possible interface.     

Simulation of driver fatigue monitoring via blink rate detection,using 65 nm CMOS technology

This paper proposes a system to detect and measure blink rate to determine fatigue levels. The method involved analysing specific frames to determine that a blink occurred, and then monitoring the time between successive blinks. The program was simulated in python using a Raspberry Pi Zero and a standard USB camera. For the blink rate detection block, a gate level schematic was implemented in Cadence software using 65 nm CMOS technology. The design was based around an asynchronous 6-bit based edge counter which was designed using D-flip-flops. The simulation calculated the average blink rate and compared this to the most recent blink rate. The outcome would determine if an alarm signal should be sent to the alarm. The system consumed 130 μA from a 1.2 V power supply.     

Beyond economics—understanding the decision-making of German small private landlords in terms of energy efficiency investment

The German government aims to achieve virtually climate-neutral building stock by 2050 to tackle climate change. To realise this goal, comprehensive policy packages based on neoclassical economic theory are in place to foster energy efficiency investment. However, in the building sector, there is increasingly a gap between this aspiration and the reality. It is claimed that one of the main reasons for this is that the existing policy framework fails to address the specific characteristics and needs of different groups of building owners. This is a particular challenge in Germany, where 80% of all dwellings are owned privately and 37% are rented out by small private landlords (SPL). Despite the significant numbers of SPL, they often follow black box decision-making processes when considering energy renovations. In this study, the author uses an explanatory model to understand the decision-making processes of SPL, combining theoretical aspects from different research disciplines. This model was applied to a low-demand housing market in a neighbourhood in the Ruhr area. Eighteen semi-structured interviews (each lasting between 37 and 115 min) were conducted, demonstrating that in addition to economic factors, the values, beliefs, norms and routines of SPL—as well as their personal capabilities and contextual factors—play an important role in their decision-making. Based on the findings, recommendations are made for enhancing the effectiveness of existing energy efficiency policies and other supporting instruments (e.g. tenancy law and social legislation), tailored to the specific needs of SPL.     

A Note on Sensitivity in Uniform Spaces

In this paper, the notions of periodic point are compared, and the sensitivity of semigroup actions on Hausdorff uniform spaces is studied. We show that for an action of a semigroup on a compact uniform space, if it is syndetically transitive and not minimal, then it is syndetically sensitive. We point out that if an action of a semigroup on a uniform space (does not need to be compact) is topologically transitive, not minimal, and has a dense set of s-periodic points, then it is syndetically sensitive. Additionally, we prove that if an action of a monoid on a uniform space (does not need to be compact) is topologically transitive, not minimal, and has a dense set of FM-periodic points, then it is syndetically sensitive.     

Surface modification technique to enhance metallurgical and mechanical properties of alloy C-276 weldment by laser shock peening without coating

Microsegregation of alloying elements is prone to hot cracking in the weldment of alloy C-276. The formation of topologically close packed phases P and µ is largely responsible for the hot cracking. The present study articulates the effect of laser shock peening (LSP) to improve the metallurgical and mechanical properties of the weld joint. The weld joint was fabricated by pulsed current gas tungsten arc welding (PCGTAW) using an ERNiCrMo-3 filler wire. LSP without coating was carried out on the cap surface of the weldment. Microstructural studies were carried out to compare the as-welded and laser-peened microstructure on the fusion zone. The results show that a fine equiaxed dendritic structure was observed in both conditions. EDS analysis was carried out to evaluate the microsegregation of alloying elements. EDS analysis indicates that there are no secondary intermetallic phases. X-ray diffraction analysis was carried out to evaluate the phase change and crystallite size in the as-welded and laser shock peened fusion zone. The result shows 48.99% reduction in crystallite size after LSP. Hardness and tensile strength results indicate there is a consequential increase in laser shock peened specimen compared with as-welded specimen.